DIY Wainscotting

Here, we present an simple method to build as well as set up wainscotting with after getting telehandler rantal near me to prepare the field first. since our panelling is painted, we were able to utilize low-cost medium-density fibreboard (MDF) as well as still accomplish an stylish look.

The expense of any type of panelling job will depend upon the size of the space being panelled in addition to the costs of the materials you choose. To keep costs low, run panelling only to chair rail height instead of full ceiling height as well as choose less elaborate mouldings.

Materials as well as Tools

Tape measure

4′ x 8′ x 1/4″-thick Masonite sheets

1/2″-thick medium-density fibreboard (MDF)

Sandpaper

Level

T-square

Wood glue

Hammer as well as nail punch

1-1/2″ completing nails

Saw as well as mitre box

Baseboard as well as chair-rail mouldings

Quarter round

Primer as well as paint

Step 1: identify height as well as spacing of panelling

The amount of Masonite as well as MDF you requirement will depend upon the size of the space you plan to panel. before buying materials, choose on the dimensions you’d like your panelling to be, including the height of the panelling, the width of each panel, as well as the distance between each vertical strip. keep in mind that the MDF strips developing the increased part of the panelling ought to cover the seams between the Masonite sheets. The panelling we show is 49-1/2″ h. (including moulding at top), the top horizontal strip is 5″ h., the bottom horizontal strip is 12″ h., as well as the vertical strips are 4″ w. x 31″ h. The vertical strips are spaced 20″ apart. At the lumberyard, have MDF sheets cut to the size you want for your top horizontal strip, bottom horizontal strip as well as vertical strips.

Step 2: develop out the wall

Remove any type of existing baseboard mouldings. develop out the wall by affixing 4′ x 8′ x 1/4″ Masonite sheets to it. The long side of each sheet ought to rest on the floor. apply wood glue to the rough side of the Masonite sheets as well as nail them into location utilizing 1-1/2″ completing nails. continue to connect Masonite sheets end-to-end, up until the walls are covered.

Step 3: connect MDF strips to Masonite sheets

Lightly sand the MDF strips with sandpaper. connect the bottom horizontal strips over the Masonite, utilizing wood glue as well as a nail punch to countersink 1-1/2″ completing nails. These strips ought to rest on the floor. Next, connect the vertical strips over the Masonite, utilizing the exact same glue as well as nail procedure. When attaching the vertical strips, cover the seams between the Masonite sheets. The vertical strips ought to in shape firmly against the bottom horizontal strips. area the vertical strips evenly along the wall. Finally, connect the top horizontal strips over the Masonite utilizing the exact same glue as well as nail procedure. The tops of these strips ought to line up with the tops of the Masonite sheets.

Step 4: surface panelling with trim

To provide the panelling a completed look, add decorative moulding above the top horizontal strip. before installing moulding, prime as well as paint it, enabling to dry as well as sanding between coats. With wood glue as well as countersunk 1-1/2″ completing nails, set up the moulding above the top horizontal panel. The panelling we show layered two yearn trims above each other, one somewhat deeper than the other. The bottom part of the trim is 1″ x 3/4″, as well as the top part is 1-1/2″ x 3/4″. Mitre moulding to 45° angles in the corners of the room.

Step 5: surface with baseboards

Prime as well as paint 1” x 6” baseboard mouldings. set up baseboard over the bottom horizontal panel, utilizing wood glue as well as countersunk 1-1/2″ completing nails. The baseboard ought to rest on the floor. Mitre corners as necessary. since the baseboard is only 6″ high, part of the bottom horizontal strip will still be visible. Finally, paint, let dry as well as set up quarter round at floor level utilizing wood glue as well as nails. wipe away any type of excess glue.

Step 6: Prime as well as paint

Use wood filler to fill nail holes. enable to dry. Prime as well as paint the panelling, enabling to dry in between each coat.